Wireless Smart-Wired-Home solutions for small homes

Wireless (Wi-Fi) Smart-Wired-Home solutions for small homes from $462

No matter how the internet is delivered to your home or office (NBN, HFC, ADSL, 4G) there still exists the problem of providing the Wi-Fi Internet signal throughout the building to be used by phones, tablets, laptops, smart-tvs, fetch boxes, Apple TV etc.

The Internet signal comes into your home or office via a telephone cable, optical fibre or HFC cable, terminated on an internal wall. A router/modem is attached to that socket (or the NBN box) and this provides internet services either via a cable or wire to your computer or by a Wireless Wi-Fi signal that is produced by the modem.

modem in lounge

The most likely location of the Modem/Router is where the telephone socket or NBN box is located. This can be in any section of the house but usually found in the lounge, study or garage.

With most modems only having a Wi-Fi range of a few meters, and not penetrating solid walls easily, this often means that non-adjoining rooms may not receive a strong enough signal to allow Wi-Fi to be used in those locations.

To transmit strong Wi-Fi signal into poor reception areas of the house or office, we recommending installing one or more Ubiquiti Wireless Access Points (WAPs) that are hard-wired (ethernet cabling) back to the modem or switch located in a data/comms cabinet (which can often be in the garage or a cupboard in an existing smart-wired house).

Wireless Access Points (WAPs)

Wi-Fi is delivered through the home or office using a series of Wireless Access Points (WAPs) . We recommend using Ubiquiti Wireless Access points in conjunction with Ubiquiti Switches and Cloud Key Controllers.

Power for the WAP’s is transmitted through the ethernet cabling, so no need to install additional power sockets in ceilings etc.

Ubiquiti Wireless access points come in two forms.

1. Unifi WAPs – Ceiling or Floor Mounted

The WAP’s resemble a small flying-saucer and range in size from 160 to 200mm diameter.

The WAP’s are strategically located at various points through the house, to provide a strong Wi-Fi signal into the required areas.

If the house or office has already been smart-wired or had ethernet wall-plates installed previously, the WAP’s can be plugged into the existing wall-plate

… and placed on a floor, under a table or in a cupboard, out of sight.

…but ideally on the ceiling to provide maximum coverage.

2. Unifi WAPs – In-Wall Mounted

Another solution is to replace the existing ethernet wall-plates socket with a wall-mounted WAP. (in-wall-wap) which provides room-wide wi-fi and includes 4 ethernet ports hidden at the base of each unit.

If no adequate existing ethernet wiring exists, then an electrician is required to install the ethernet cabling. The Ubiquiti WAPs are ideally located on the ceiling, with ethernet cabling being run back to the modem, switch or central hub.


Proposed solution for small homes

For the IT Guys to deploy a single WAP solution for a small house with existing smart wiring within 10k of Subiaco, the estimated cost would be $462 inc GST (plus extra travel time if outside 10k plus additional cabling, power boards etc not supplied by client)

If ethernet cabling is required, an electrician will need to be employed and depending on the building construction could cost anywhere between $150 and $600.

If you would like us to quote you on this or a larger house/office wireless networking solutions, please contact us as detailed below.

Need more help?

If you live in Western Australia, and you need any kind of computer help, please bring your computer to us at 315 Rokeby Road, Subiaco, Western Australia or call us out. You can contact us here or call:

08 6365 5603 
Alternatively click on the Green “Support” button in the bottom right hand corner of the screen and leave a message.Microsoft Silver Certified Partner - Small and Midmarket Cloud SolutionsFor instant remote control support download and install our TeamViewer remote control software By Clicking Here and following the instructions found on this page